What are Flanges & Types of Flanges
Flanges |
The flange is the circle with holes inserted and welded around a pipe to connect them together. Of course in those holes appropriate bolts are placed and sometimes flange protections of rubber or other material, are inserted between the two flanges, in order to better close the joint and prevent leakage of liquid or gas.
In other words, a flange is a mechanical coupling section between two parties not directly welded, not permanent, and united through bolts or screws.
A flange is a forged or cast ring of steel designed to connect sections of pipe or join pipe to a pressure Vessel, pump or any other integral flanges assembly.
Flanges are joined to each other by bolting and joined to the piping system by welding or threading.
The basic types of flanges are; Slip on, Blind, Weld Neck, Threaded, Socket Weld, Lap Joint and Orifice.
Flanges are designed to the following pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.
The most common facings machined on flanges are:
(a) Raised face, 1/16 inch for 150lb and 300lb, ¼ inch for 400lb and heavier.
(b) Flat face, for 150lb and 300lb only, other may be flat face on request.
(c) Ring type joint, may be applied to all pressure ratings.
TYPES & APPLICATIONS
Slip-On Flange
Slip-On Flange (SORF) |
The flange is slipped over the pipe and then welded both inside and outside to provide sufficient Strength and prevent leakage. This flange is used in preference to weld necks by many users because of its lower cost and the fact that less accuracy is required when cutting pipe to length.
Blind Flanges
Blind Flange (BLRF) |
This is a flange without a bore and is used to shut off a piping system or vessel opening. It also permits Easy access to vessels or piping systems for inspection purposes. Blind flange can be supplied with or without hubs at the manufacturers option.
Weld-Neck Flange
Weld-Neck Flange (WNRF) |
This is designed to be joined to a piping system by buttwelding. It is relatively expensive because of Its long neck, but is preferred for high stress applications. The neck, or hub transmits stresses to the the base of the hub to the wall thickness at the butt weld, provide important reinforcement of the flange. The bore of the flange matches the bore of the pipe, reducing turbulence and erosion.
Threaded Flange
Threaded Flange |
This is similar to a slip-on flange in outline, but the bore is threaded, thus enabling assembly without welding. This obviously limits its application to relatively low pressure piping systems. The flange may be welded around the joint after assembly, but this is not considered a satisfactory method of increasing its applications.
Socket Weld Flanges
Socket-Weld Flange (SWRF) |
This is similar to a slip-on flange in outline, but the bore is counter-bored to accept pipe. The diameter of the remaining bore is the same as the inside diameter of the pipe. The flange is attached to the pipe by a fillet weld around the hub of the flange. An optional interval weld may be applied in high stress applications. It’s biggest use is in high pressure systems such as hydraulic and steam lines.
Spectacle Flanges
Spectacle Flange |
This is a pressure retaining plate with one solid end and one open end connected with a web or tie-bar. In normal operation, the open end forms the seal between two flanges and permits normal flow of fluid through pipe work. If the solid end is swung into position it effectively blanks of the pipe and halts the flow.
Lap-Joint Flanges
Lap-Joint Flange (LJRF) |
This is again similar to a slip-on flange, but it has a radius at the intersection of the bore and the flange face to accommodate a lap stub end. The face on the stub end forms the gasket face on the flange. This type of flange is used in applications where section of piping systems need to be dismantle quickly and easily for inspection or replacement.
Orifice Flanges
Orifice Flange |
The function of an orifice flange is to provide access to a line for metering of gases or liquids. An orifice plate is clamped between a pair of flanges when installed in a line and the whole assembly is refer to as an orifice flange union. Jack-screws within the assembly facilitate removal of the orifice plate. The orifice plate, the metering device, consists of a thin plate with a concentric, square edge, circular hole in the centre. Two pressure tap-holes are drilled in each flange to measure pressure difference through the orifice.
Groove & Tongue Flanges
Ring Type Joint Flange (RTJ) |
The Groove and Tongue faces of these flanges must be matched. One flange face has a raised ring (Tongue) machined onto the flange face while the mating flange has a matching depression (Groove) machined into it's face.
Tongue-and-groove facings are standardized in both large and small types. They differ from male-and-female in that the inside diameters of the tongue-and-groove do not extend into the flange base, thus retaining the gasket on its inner and outer diameter. These are commonly found on pump covers and Valve Bonnets.
Tongue-and-groove joints also have an advantage in that they are self-aligning and act as a reservoir for the adhesive. The scarf joint keeps the axis of loading in line with the joint and does not require a major machining operation.
General flange faces such as the RTJ, T&G and the F&M shall never be bolted together. The reason for this is that the contact surfaces do not match and there is no gasket that has one type on one side and another type on the other side.
Long Neck Flanges
Long Weld Neck Flange (LWNRF) |
Owing to our rich industrial experience, we are offering a comprehensive range of Long Weld Neck Flanges. The professionals of our organization source these neck flanges from trusted vendors. These flanges are unique due to their simple connectivity with other pipes. Moreover, our products are extensively used in refining industries for linking purposes. Our esteemed patrons can avail these qualitative range of flanges from us at industry-leading prices.
Flat Face Flanges
Flat Face Flange (FF) |
The Flat Face (FF) flange has a gasket surface in the same plane as the bolting circle face. Applications using flat face flanges are frequently those in which the mating flange or flanged fitting is made from a casting.
Flat face flanges are never to be bolted to a raised face flange. ASME B31.1 says that when connecting flat face cast iron flanges to carbon steel flanges, the raised face on the carbon steel flange must be removed, and that a full face gasket is required. This is to keep the thin, bittle cast iron flange from being sprung into the gap caused by the raised face of the carbon steel flange.
Raised Face Flanges
Raised Face Flange (RF) |
The Raised Face (RF) type is the most applied flange face, and is easily to identify. It is referred to as a raised face because the gasket surfaces are raised above the bolting circle face.
Specifications covering the manufacture and dimensions of flanges:
ANSI B16.5 Standard 150# & 300# Class |
ANSI B16.5 Standard 600# & 900# Class |
ASTM SPECIFICATIONS
ASTM specifications regulate approved raw materials for which flanges can be made and specifications .
For stainless flanges are:
ASTM A.182 - Forged or Rolled Alloy Steel Pipe Flanges & Fittings for high temperature service.
ANSI AND MSS SPECIFICATIONS
The standards govern the dimensions and tolerances to which fitting are manufactured:
ANSI B. 16.5 - Steel Pipe Flanges and Flanged Fittings (½ inch to 24 inch nominal diameter)
MSS SP.6 - Flange Facings
MSS SP.25 - Marking of flanges
MSS SP.39 - Bolts and Nuts for Flanges
MSS SP.44 - Large Diameter Pipeline Flanges. (Over 24 inch dia)
API-605 - Large Diameter Flanges for petroleum Usage. (Over 24 inch dia)
The ASME Code is not a standard as such but section VIII provides the procedure for calculating dimensions
For all pressurised vessels flanges.
The following are not flange specifications but they influence the manufacture of forged steel flange
ANSI B. 31.10 - Code for Pressure Piping
ANSI B. 31.3 - Petroleum Refinery Piping
ANSI B. 31.4 - Oil Transportation Piping
ANSI B. 31.5 - Refrigeration Piping Systems
ANSI B. 31.7 - Nuclear Power Piping
ANSI B. 31.8 - Gas Transmission and Distribution Piping systems
ANSI B. 36.10 - Standard for Wrought Steel pipe
ANSI B. 36.19 - Standard for Stainless Steel Pipe
ANSI B. 16.10 - Valve Dimensions Face & End
FLANGES |
Hitesh Mehta
www.facebook.com/anitasteelmetals
www.facebook.com/anitasteelmetals
This comment has been removed by a blog administrator.
ReplyDeleteThanks for your efforts in sharing this post with us. This was really awesome. kindly keep continuing the great work.
ReplyDeletestainless steel flanges suppliers
You made such an interesting piece to read, giving every subject enlightenment for us to gain knowledge. Thanks for sharing the such information with us.
ReplyDeleteStainless Steel Flange
This is most informative and also this post most user friendly and super navigation to all posts.
ReplyDeleteFlanges
Great Article! Thanks for sharing such an amazing information about SS Flanges.
ReplyDeleteKeep Sharing such great content!
It is really a helpful blog to find some different source to add my knowledge. alloy steel flanges
ReplyDeleteGreat blog ! I am impressed with suggestions of author. slip on flange manufacturer
ReplyDeleteI read your blog now share great information here. API 5L Seamless Pipe suppliers in India
ReplyDeleteI am thankful to this blog giving unique and helpful knowledge about this topic. Inconel 625 Round Bar
ReplyDeleteThis blog is really helpful to deliver updated affairs over internet which is really appraisable. Hastelloy c276 Tube
ReplyDeleteShare great information about your blog , Blog really helpful for us . copper nickel pipe suppliers
ReplyDeleteThanks for share your blog here . Stainless Steel 304 Flanges
ReplyDeleteOutstanding as well as powerful suggestion by the writer of this blog site are truly valuable to me.
ReplyDeleteP22 Pipe suppliers
We read your blog website, share most practical information in blog.
ReplyDeleteFlanges Manufacturer In India
great blog, thanks for the information, Steel Pipes Tube USA
ReplyDeleteThanks for sharing thoughts. However, Siddhigiri is leading Hastelloy C276 Round Bar Manufacturers & supplies worldwide.
ReplyDeleteI was looking for information regarding Super Duplex Steel S32205 Flanges & Stainless Steel 310/310S Flanges and I Found Your Blog. You have given very well information about Flanges and its type are also explained in very detailed Manner. This Information will come very handy for my purpose. Thank You very Much.
ReplyDeleteI just visited your blog while I was searching for SMO 254 Flanges Supplier with Super Duplex Steel 32750 and 32760 Flanges Supplier. It contains enough information about Types of Flanges and I have bookmarked your blog for future reference. You have really done the in-depth research to produce this kind of information. Great work.
ReplyDeleteI want to share some more details about qualities seamless pipe dealers:-
ReplyDeleteFollowing are the highlights of our seamless pipes that stand out from the Pipes of different dealers: –
Our colleagues from whom we get these pipes utilize first class unrefined substance for making pipes with ideal molding under the right warming temperature.
More modest distance across seamless pipes are helpful in many fields. Different aspect pipes are presented by JRS pipes and tubes, in light of which clients can get empty estimated Pipes, as per their prerequisites with the goal that they don't confront any issues in finishing their task.
We offer pipes having solid welding capacity and high pressure ability. This guarantees the client with substantial power engrossing power. They can oppose this much tension without any problem.
Pipes have thick metal invigorating them extra and solid undertaking finish functionality.
Precisely done fixing of these pipes makes their surface smooth.
JRS Pipes and tubes is famous as best seamless pipe dealers in whole India.
Hello! This is my first visit to your blog! We are a group of volunteers and starting a new initiative in a community in the same niche. Your blog provided us useful information to work on. You have done a marvellous job!Jindal Hissar Dealers Delhi NCR
ReplyDeleteThanks for sharing such informative blog on types & details on Stainless Steel Flanges & how Stainless Steel Flanges Manufacturer provide the quality product.
ReplyDeleteKeep sharing such informative posts. Best valves and strainers supplier offers Pipe Fittings. We offer high quality Pipe Fittings at low cost.
ReplyDeleteCheck Valve manufacturers
This is nice post. Thank you for sharing this blog. hastelloy c276 flange specification
ReplyDelete